[. . . ] Do not use attachments not recommended by the appliance manufacturer as they may cause hazards. Do not use this appliance near water - for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, etc. The appliance may fall, causing serious injury to a child or adult, and serious damage to the appliance. Use only with a cart or stand recommended by the manufacturer, or sold with the appliance. [. . . ] The light will appear blinking when troubles occur during startup and the error details will be displayed in CH1-CH4. CH1 CH2 CH3 CH4 Error Description A device with the same IP address as VN-900 is detected. The normal display will be restored upon input of video signals. G [O. L] Overload Lamp Displays the processing load of VN-900. This light is turned on when the processing load of VN-900 is too heavy. I [CH1] Video 1 Channel Lamp Displays the image transmission status of VN-900. J [CH2] Video 2 Channel Lamp Displays the image transmission status of VN-900. K [CH3] Video 3 Channel Lamp Displays the image transmission status of VN-900. L [CH4] Video 4 Channel Lamp Displays the image transmission status of VN-900. Turns off when there is no transmission. Light OFF Light OFF Light OFF Light ON Light OFF Light OFF Light ON Light OFF F [ALM] Alarm Lamp Displays alarm input to VN-900. Lights up when there are changes in the alarm input or when motion is detected. The light will turn off automatically after 5 seconds. 6 [Back] M AUDIO VIDEO INPUT RS CONTROL COM1 SERVICE OUTPUT T W ALARM RS-232C RS-485 IN 1CH 2CH COM OUT 1 2 PUSH 3 4 G INPUT OUT 3CH 4CH COM2 10BASE-T/100BASE-TX RESET DC 5V N O P Q U VX M [AUDIO IN] terminal (RCA pin) For input of audio signals. Fasten each end using 1 M3 screw and 2 M4 screws that are supplied with the rack mount bracket. ) 2. Fasten to the rack using the M5 screws supplied with the rack mount bracket (2 M5 screws at each end) 2. 1. PO WE R LIN K 100M FD X /CO L ST S AL M O. L AU D CH 1 CH 2 CH 3 CH 4 1. 2. In case of 2 units. Mount the joint bracket to the connecting face of the unit (Remove 3 screws from VN-900. Connect with 3 M3 screws that are supplied with the rack mount bracket. ) 2. Fasten the 4 locations (top and bottom) using the M3 screws supplied with the rack mount bracket (For joining the left and right units) 3. Mount the side bracket on both left and right (Remove 1 screw from each end of VN-900. Fasten each end using 1 M3 screw and 2 M4 screws that are supplied with the rack mount bracket. ) 4. Fasten to the rack using the M5 screws supplied with the rack mount bracket (2 M5 screws at each end) 2. 4. POW ER LINK 100 M FDX /CO L STS ALM O. L AUD CH1 CH2 CH3 CH4 1. POW ER LINK 100 M FDX /CO L STS ALM O. L AUD CH1 CH2 CH3 CH4 3. 2. 10 4. IP Address Setting There are 2 ways to set the IP address of VN-900. (A) Assigning IP address to VN-900 from the DHCP server (B) Assigning a static IP address to VN-900 upon turning off the DHCP client function of VN-900 (A) Assigning IP Address from the DHCP Server The DHCP client function is set to ON in the factory settings of VN-900. By assigning an IP address from the DHCP server, VN-900 can be connected to the network without manual setting of IP address. [. . . ] https://192. 168. 0. 2/e4viewer/e4monitor. html A Enter the URL of built-in viewer of the unit. (In factory setting, https://192. 168. 0. 2/e4viewer/e4monitor. html is the URL when there is no DHCP server. ) B Click AGoB. MEMO Direct specification of the IP address may not be possible when a proxy server is used for Internet access. When a security warning screen appears, click the AOKB button to proceed. 2. Enter the user name and password. A Enter user name of administrator. The viewer will be installed and launched. 19 (3) Operating the viewer "Image Selection" Use the ACH1-CH4B buttons to select the video channel to display. [. . . ]